Wing Wing Z84 and INAV – Part 1 – Components

 

 

 

 

 

 

 

 

I’ve been wanting to build an FPV flying wing for some time.  I actually have an FX-79 kit and accompanying PixHawk flight controller sitting in my workshop, they have been there for a while but the Arduplane setup is a little intimidating and I have found myself unable to commit the time to getting started.

A little while ago I saw some reviews of the Wing Wing Z84 – the smaller sibling of the FX-79 with a wingspan of 845mm (~33in).  It looked compact, low cost and ideally sized to re-purpose some old quadcopter parts I had hanging around.

Perhaps combined with a simpler flight controller for stabilisation this could provide a simpler entry point in to fixed wing FPV?

The kit was promptly ordered from Banggood and I began to look at the other parts I’d use to complete the build.

Electronic Components

My plan here was to keep the build cheap and use as much as possible from my parts bin.  It’s always nice to find a use for old and defunct components – which tend to build up over the years if you like to tinker.

Servos

A few unused HK900 9g servos which have been sitting in a drawer for 4-5 years finally found a home (they fitted the cutouts in the Z84 wing perfectly).  Anything of a similar spec would work fine.  As the model is relatively lightweight I doubt the servo performance needs to be too much of a consideration.

Motor

The powerplant I went with was an old Quantum 1806 2300KV brushless outrunner.  I have seen a large number of builds using a more powerful 2204/2205 motor however I had quite a few of the 1806’s in the parts bin recovered from an old quadcopter.  Any similar size motor should do the job. There was a risk this would be underpowered but could also help provide better flight times.  It can easily be upgraded in future if necessary.

ESC

An unused 12A HK-Blue ESC was used here – again anything similar would be fine.  I have quite a few of these, most of which have been flashed with SimonK firmware.  Unfortunately that firmware does not support braking functions which are handy for a flying wing – particularly if you want to glide and reduce the number of props broken on landing.

I found one with the stock firmware that I had as a spare.  If you know of an ‘aero’ firmware supporting braking that can be flashed to these ESCs please do leave a comment as I’d love to be able to re-use some of the others that I have.

Battery

The Turnigy Nano-tech 45C 3S 1500mah LiPO packs that I have from my early days of flying quadcopters will fit the airframe perfectly and should provide reasonably good flight times.

FPV Camera

I didn’t have a spare FPV camera so purchased a cheap Eachine 1000TVL CCD camera from Banggood.

VTX

An old FX48 5.8Ghz VTX from the parts bin seemed to be prefect for this.

RC Receiver

I had an FRsky X4R-SB receiver sitting around.  Any SBUS capable receiver would be fine although the X8R will be on the large side.

GPS

The Ublox-M8N GPS module that came with my PixHawk would do just fine.

Flight Controller

Originally I hoped to re-purpose an old Flip32+ or CC3D flight controller for stabilisation.  After some research on firmwares providing stabilisation for flying wings it became clear that these would not be up to the task, at least not for anything more than the most basic accelerometer/gyro based stabilisation.  Features like GPS based heading hold and return to home would not be available.  This is not only due to limitations in processing power but also the limited number of UART ports.

I settled on the OMNIBUS F3 AIO Pro with barometer.  This has all the power and functionality required to run INAV – a branch from the Cleanflight firmware which is specifically focused on GPS based flight control and particularly well suited to fixed wing aircraft (it can also be used for multirotors).  The flight controller uses Micro JST SH 1.0mm style plugs for various I/O so I also purchased a set of pre-wired plugs to adapt for use with some of the external components.  We need 4 and 6 pin cables for this board so I ordered a set of each.

There is an F4 version of the OMNIBUS available which has more processing power than the F3 however the F4 based boards UART ports sometimes require external inverters.  The F3 board UART ports all have software selectable inverters so in my opinion are a bit more flexible and better to work with.

3D Printed Parts

In preparation for the build I had a browse through Thingyverse to see if there were any useful components to make the Z84 build cleaner or solve issues I have yet to encounter.

The first thing I found was a motor mount designed specifically for 1806 motors.

Next I came across a neat little FC/GPS mounting stack which looked rather attractive.

I had to remix/design my own GPS mount for this stack as my M8N module needs to be mounted at a 45′ offset so that the onboard magnetometer is oriented correctly.

These parts were promptly printed in PLA+ in preparation for the arrival of the Z84 kit and outstanding components.

Watch out for the next part of this series where I’ll cover assembly of the kit and components above.

This blog isn’t intended as a complete step-by-step build guide but more of an account of my experiences.  With that in mind it does assume the reader has some previous experience in building RC models and/or tinkering with electronics.  That said if you are a beginner and have any questions feel free to leave a comment and I’ll do my best to help you out.

JF.